230V COB IP65 LED Strip Light Troubleshooting & Recommendations

Common Issues & Solutions

LED strip won't turn on

• Check that the 230V AC supply is switched on and available.
• Check all wiring connections, connectors, plugs, and terminals.
• Ensure the strip is correctly connected according to the manufacturer's instructions.
• Check that the electrical circuit and protection devices are functioning correctly.
• Inspect connections for loose wiring, damage, or signs of moisture ingress.

Strip is dim or unevenly lit

• Check for loose or damaged electrical connections.
• Confirm that the strip is receiving the correct mains voltage.
• Check for damaged sections of LED strip.
• Ensure the installation does not exceed the manufacturer's recommended maximum continuous run length.
• Inspect connections and joints for moisture, corrosion, or damage.

Only part of the strip lights up

• Inspect the strip for cuts, physical damage, or signs of moisture ingress.
• Check connectors and joints to ensure they are properly secured.
• Inspect cut ends and waterproof seals for damage.
• Test sections individually, where safe to do so, to help identify the faulty section.
• Replace damaged sections or components where necessary.

Flickering lights

• Check for loose or poor electrical connections.
• Confirm that the mains supply is stable.
• Check that any dimmer or controller being used is compatible with the specific 230V LED strip.
• Inspect connectors and joints for corrosion, moisture, or damage.
• If flickering persists, have the installation checked by a qualified electrician.

Adhesive won't stick

• Clean the mounting surface thoroughly before installation.
• Ensure the surface is smooth, dry, and free from dust, grease, and other contaminants.
• Make sure the strip is firmly pressed onto the mounting surface.
• Consider using an aluminium LED profile or suitable mounting clips for a more secure long-term installation.

Recommendations

• Use a suitable 230V AC supply and ensure the electrical circuit is correctly rated for the total strip load.
• Install the strip on a suitable mounting surface or in an aluminium profile where appropriate to improve heat dissipation and provide a professional finish.
• Avoid sharp bends, twisting, folding, or exceeding the manufacturer's minimum bend radius.
• Never power the strip while it is still tightly rolled on the reel, as heat can build up and damage the LEDs.
• Do not exceed the manufacturer's recommended maximum continuous run length.
• Select an appropriate IP rating for the installation environment. IP65 provides protection against dust and water jets but is not designed for immersion.
• Properly seal all cut ends, connectors, and connection points after modifying the strip to help maintain its IP65 protection.
• Always test the strip before permanently mounting it.
• Disconnect the mains power before cutting, connecting, modifying, or servicing the LED strip.
• Use compatible dimmers and controllers only where the specific 230V LED strip supports them.

Following these recommendations will help maximise the performance, reliability, moisture protection, and lifespan of your 230V COB IP65 LED Strip Light while reducing the likelihood of installation issues.

230V COB IP65 LED Strip Light Safety Tips

To ensure safe installation and reliable operation, follow these important safety guidelines:

• Always disconnect the 230V mains power before installing, cutting, connecting, or modifying the LED strip.
• Only use the LED strip with the correct 230V AC supply specified by the manufacturer.
• Never connect a 230V LED strip to a 12V or 24V DC power supply.
• Never power the strip while it is tightly wound on the reel, as heat buildup can damage the LEDs.
• Install the strip on a clean, dry, suitable, and heat-resistant mounting surface.
• Use an aluminium LED profile where appropriate to improve heat dissipation and provide additional physical protection.
• Avoid excessive bending, twisting, or folding, and only cut the strip at the manufacturer's designated cut points.
• Ensure all electrical connections are secure, properly insulated, and protected.
• For outdoor or damp environments, ensure the IP65 rating is suitable for the specific application and that all connections and cut ends are properly sealed.
• IP65 does not mean the strip can be submerged in water. Do not install it in applications where it will be permanently underwater or exposed to conditions beyond its rating.
• Do not assume the strip's IP65 rating applies to connectors, plugs, terminals, controllers, or other electrical components. Each component must be appropriately rated for its environment.
• Keep electrical connections protected from standing water and direct exposure to excessive moisture.
• Ensure adequate ventilation around electrical components and avoid covering them with insulation or other materials that could cause overheating.
• If connecting the strip directly to mains electricity, installation should be carried out by a qualified electrician in accordance with local electrical regulations.
• Regularly inspect the installation for loose connections, damaged cables, cracked waterproof coatings, corrosion, or signs of overheating.
• Keep the LED strip, wiring, and electrical connections away from flammable materials.

Following these safety precautions will help ensure a safe installation, reliable performance, effective moisture protection, and a long service life for your 230V COB IP65 LED Strip Light.